$6.00 – $68.00
The SFP transceiversare high performance, cost effective modules supporting datarate of 125Mbps/155Mbps and 10km transmission distance with SMF.
The transceiver consists of three sections: a FP laser transmitter,a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements.
The transceivers are compatible with SFP Multi-Source Agreement and SFF-8472 digitaldiagnostics functions.
Standard: 0 to +70°C
Industrial: -40 to +85°C
| Parameter | Symbol | Min | Typical | Max | Unit | Notes | |
| Transmitter | |||||||
| Centre Wavelength | λc | 1260 | 1310 | 1360 | nm | ||
| Spectral Width（RMS） | Δλ | 3 | nm | ||||
| Side-Mode Suppression Ratio | SMSR | – | – | – | dB | ||
| Average Output Power | Pout | -14 | -8 | dBm | 1 | ||
| Extinction Ratio | ER | 9.0 | dB | ||||
| Data Input Swing Differential | VIN | 180 | 1200 | mV | 2 | ||
| Input Differential Impedance | ZIN | 90 | 100 | 110 | Ω | ||
| TX Disable | Disable | 2.0 | Vcc | V | |||
| Enable | 0 | 0.8 | V | ||||
| TX Fault | Fault | 2.0 | Vcc | V | |||
| Normal | 0 | 0.8 | V | ||||
| Receiver | |||||||
| Centre Wavelength | λc | 1260 | 1610 | nm | |||
| Receiver Sensitivity | -32 | dBm | 3 | ||||
| Receiver Overload | -8 | dBm | 3 | ||||
| LOS De-Assert | LOSD | -33 | dBm | ||||
| LOS Assert | LOSA | -45 | dBm | ||||
| LOS Hysteresis | 0.5 | 4 | dB | ||||
| Data Output Swing Differential | Vout | 600 | 800 | 1000 | mV | 4 | |
| LOS | High | 2.0 | Vcc | V | |||
| Low | 0.8 | V | |||||
Notes:
| Parameter | Symbol | Min | Typical | Max | Unit |
| Tx Disable Negate Time | t_on | 1 | ms | ||
| Tx Disable Assert Time | t_off | 10 | µs | ||
| Time To Initialize, including Reset of Tx Fault | t_init | 300 | ms | ||
| Tx Fault Assert Time | t_fault | 100 | µs | ||
| Tx Disable To Reset | t_reset | 10 | µs | ||
| LOS Assert Time | t_loss_on | 100 | µs | ||
| LOS De-assert Time | t_loss_off | 100 | µs | ||
| Serial ID Clock Rate | f_serial_clock | 100 | 400 | KHz | |
| MOD_DEF (0:2)-High | VH | 2 | Vcc | V | |
| MOD_DEF (0:2)-Low | VL | 0.8 | V |
| Parameter | Range | Unit | Accuracy | Calibration |
| Temperature | 0 to +70 | °C | ±3°C | Internal |
| -20 to +80 | ||||
| -40 to +85 | ||||
| Voltage | 3.0 to 3.6 | V | ±3% | Internal |
| Bias Current | 0 to 100 | mA | ±10% | Internal |
| TX Power | -14 to -8 | dBm | ±3dB | Internal |
| RX Power | -32 to -6 | dBm | ±3dB | Internal |
The transceivers provide serial ID memory contents and diagnostic information about the present operating conditions by the 2-wireserial interface (SCL, SDA).
The diagnostic information with internal calibrationor external calibration all are implemented, including received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring.
The digital diagnostic memory map specific data field defines as following
| Pin | Signal Name | Description | Plug Seq. | Notes |
| 1 | VEET | Transmitter Ground | 1 | |
| 2 | TX FAULT | Transmitter Fault Indication | 3 | Note1 |
| 3 | TXDISABLE | Transmitter Disable | 3 | Note2 |
| 4 | SDA | SDA Serial Data Signal | 3 | |
| 5 | SCL | SCL Serial Clock Signal | 3 | |
| 6 | MOD_ABS | Module Absent. Grounded within the module | 3 | |
| 7 | RS0 | Not Connected | 3 | |
| 8 | LOS | Loss of Signal | 3 | Note 3 |
| 9 | VEER | Receiver ground | 1 | |
| 10 | VEER | Receiver ground | 1 | |
| 11 | VEER | Receiver ground | 1 | |
| 12 | RD- | Inv. Received Data Out | 3 | Note 4 |
| 13 | RD+ | Received Data Out | 3 | Note 4 |
| 14 | VEER | Receiver ground | 1 | |
| 15 | VCCR | Receiver Power Supply | 2 | |
| 16 | VCCT | Transmitter Power Supply | 2 | |
| 17 | VEET | Transmitter Ground | 1 | |
| 18 | TD+ | Transmit Data In | 3 | Note 5 |
| 19 | TD- | Inv. Transmit Data In | 3 | Note 5 |
| 20 | VEET | Transmitter Ground | 1 | |
Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.
2) Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3) LOS is open collector output. Should be pulled up with 4.7k~10kΩ on host board to a voltagebetween 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
4) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be terminated with 100Ω (differential) at the user SERDES.
5) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.
Part Number | Product Description |
HNSFP-FE31-FX | 155M SFP 1310nm 2km |
HNSFP-FE31-FXI | 155M SFP 1310nm 2km |
HNSFP-FE31-LX | 155M SFP 1310nm 10km |
HNSFP-FE31-LXI | 155M SFP 1310nm 10km |
HNSFP-FE31-LX20 | 155M SFP 1310nm 20km |
HNSFP-FE31-LH40 | 155M SFP 1310nm 40km |
HNSFP-FE55-ZX | 155M SFP 1550nm 80km |
HNSFP-FE55-ZX100 | 155M SFP 1550nm 100km |
HNSFP-FE55-ZX160 | 155M SFP 1550nm 160km |
HNSFP-FE31-FX | 155M SFP 1310nm 2km |
Reviews
There are no reviews yet.